Motor-manual tree felling by chainsaws remains a widespread but hazardous forestry practice. This operation consists of executing a directional notch followed by a felling cut that releases a hinge. The hinge geometry (defined by its height, width, and alignment relative to the directional notch) is a critical determinant of safe felling, controlling the direction and stability of the falling tree. Although hinge geometry is prescribed in felling guidelines on the basis of field experience, its effect on the mechanical response of the hinge has not been quantified. This study evaluates variations in hinge flexibility and bending stiffness using wooden square beams of European beech (Fagus sylvatica) and silver fir (Abies alba) in a rig reproducing the classical felling cuts, varying hinge geometry combinations. Two geometric parameters, back-cut height (S) and hinge width (C) were examined. Mechanical testing was performed using a universal testing machine, and load–deformation curves were smoothed with a Savitzky–Golay filter; the Critical Bending Angle and Yield Point were determined by using the 0.02◦ offset method and absorbed energy by Simpson integration. Results reveal different mechanical behavior between the two dimensions: hinge width primarily determines yield force, whereas back-cut height governs flexibility, showing a strong negative correlation with the critical bending angle. Significant species-specific differences were observed for both response variables. Hinge toughness, expressed as absorbed energy per unit hinge cross-section, was found to be independent of back-cut height and about 1.8 times higher in beech (0.39 kJ·m−2) than in fir (0.22 kJ·m−2).

Foderi, C., Neri, F., Fabiano, F., Calamai, S., Laschi, A., Togni, M. (2026). Tree Felling by Chainsaw: A Laboratory Assessment of the Hinge Flexibility in Relation to Its Width and to the Back-Cut Height. FORESTS, 17(11) [10.3390/f17111272].

Tree Felling by Chainsaw: A Laboratory Assessment of the Hinge Flexibility in Relation to Its Width and to the Back-Cut Height

Laschi, Andrea;Togni, Marco
2026-10-23

Abstract

Motor-manual tree felling by chainsaws remains a widespread but hazardous forestry practice. This operation consists of executing a directional notch followed by a felling cut that releases a hinge. The hinge geometry (defined by its height, width, and alignment relative to the directional notch) is a critical determinant of safe felling, controlling the direction and stability of the falling tree. Although hinge geometry is prescribed in felling guidelines on the basis of field experience, its effect on the mechanical response of the hinge has not been quantified. This study evaluates variations in hinge flexibility and bending stiffness using wooden square beams of European beech (Fagus sylvatica) and silver fir (Abies alba) in a rig reproducing the classical felling cuts, varying hinge geometry combinations. Two geometric parameters, back-cut height (S) and hinge width (C) were examined. Mechanical testing was performed using a universal testing machine, and load–deformation curves were smoothed with a Savitzky–Golay filter; the Critical Bending Angle and Yield Point were determined by using the 0.02◦ offset method and absorbed energy by Simpson integration. Results reveal different mechanical behavior between the two dimensions: hinge width primarily determines yield force, whereas back-cut height governs flexibility, showing a strong negative correlation with the critical bending angle. Significant species-specific differences were observed for both response variables. Hinge toughness, expressed as absorbed energy per unit hinge cross-section, was found to be independent of back-cut height and about 1.8 times higher in beech (0.39 kJ·m−2) than in fir (0.22 kJ·m−2).
23-ott-2026
Settore AGRI-03/C - Tecnologia del legno e utilizzazioni forestali
Foderi, C., Neri, F., Fabiano, F., Calamai, S., Laschi, A., Togni, M. (2026). Tree Felling by Chainsaw: A Laboratory Assessment of the Hinge Flexibility in Relation to Its Width and to the Back-Cut Height. FORESTS, 17(11) [10.3390/f17111272].
File in questo prodotto:
File Dimensione Formato  
forests-17-01272-v2.pdf

accesso aperto

Tipologia: Versione Editoriale
Dimensione 5.2 MB
Formato Adobe PDF
5.2 MB Adobe PDF Visualizza/Apri

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/10447/721583
Citazioni
  • ???jsp.display-item.citation.pmc??? ND
  • Scopus ND
  • ???jsp.display-item.citation.isi??? ND
social impact