This work presents the fabrication of femtoliter-scale oil droplets by inkjet printing based on a novel mechanism for the spontaneous fragmentation at the interface with an immiscible water phase and the electrical characterization of the resulting immersed “daughter” droplets. [1] In particular, picoliter-scale fluorinated oil droplets impact on surfactant laden water phase at moderately high Weber number (101), and are subjected to spreading and capillary instabilities at the water/air interface which ultimately lead to rupture in smaller sized droplets, according to reported models for macroscale droplets systems - [2] the emerging fragmentation results in “daughter” droplets having volumes of about 10-30 % with respect to the initial droplet volume. Remarkably, the picoliter scale downscaling leads to a novel surfactant-driven fragmentation due to the low Bond number (around 10-4-10-5), meaning that droplet immersion is dependent on surface tension forces and not on gravitational forces. In fact, the non-ionic Polyoxyethylene (20) sorbitan monolaurate was observed to permit the droplet immersion in the water phase only if spiked in the water phase at concentrations equal or higher than its critical micellar concentration (i.e. around 0.003% v/v). The resulting oil “daughter” droplets are characterized by a chip with integrated microelectrodes, permitting to extract number, velocities and diameter distribution (peaked at about 3 m) employing electrical impedance measurements. In accordance with reported models, the electrical characterizations show that the droplets have volumes in the femtoliter scale and are subjected to inertial focusing. [3] This work can be considered an important advancement for understanding the effects of downscaling on fragmentation phenomena at immiscible interfaces, leading to a knowledge platform for a tailored oil droplets fabrication applicable for drug encapsulation, pharmaceutic preparations, and thin-film wrapping around droplets. [4] Bibliography 1. D. Spencer, F. Caselli, P. Bisegna and H. Morgan., Lab Chip, 2016, 16, 2467. 2. H. Lhuissier, C. Sun, A. Prosperetti, and D. Lohse, Phys. Rev. Lett., 2013, 110, 3. G. Arrabito, V. Errico, A. De Ninno, F. Cavaleri, V. Ferrara, B. Pignataro, and F.Caselli, Langmuir, 2019, 35, 4936. 4. D. Kumar, J. D. Paulsen, T. P. Russell, N. Menon, Science, 2018, 359, 775.

Giuseppe Arrabito, V.E. (2019). Spontaneous Interfacial Fragmentation of Inkjet Printed Oil Droplets and Their electrical characterization. In Book of Abstracts - FISMAT 2019.

Spontaneous Interfacial Fragmentation of Inkjet Printed Oil Droplets and Their electrical characterization

Giuseppe Arrabito;Felicia Cavaleri;Vittorio Ferrara;Bruno Pignataro;
2019-01-01

Abstract

This work presents the fabrication of femtoliter-scale oil droplets by inkjet printing based on a novel mechanism for the spontaneous fragmentation at the interface with an immiscible water phase and the electrical characterization of the resulting immersed “daughter” droplets. [1] In particular, picoliter-scale fluorinated oil droplets impact on surfactant laden water phase at moderately high Weber number (101), and are subjected to spreading and capillary instabilities at the water/air interface which ultimately lead to rupture in smaller sized droplets, according to reported models for macroscale droplets systems - [2] the emerging fragmentation results in “daughter” droplets having volumes of about 10-30 % with respect to the initial droplet volume. Remarkably, the picoliter scale downscaling leads to a novel surfactant-driven fragmentation due to the low Bond number (around 10-4-10-5), meaning that droplet immersion is dependent on surface tension forces and not on gravitational forces. In fact, the non-ionic Polyoxyethylene (20) sorbitan monolaurate was observed to permit the droplet immersion in the water phase only if spiked in the water phase at concentrations equal or higher than its critical micellar concentration (i.e. around 0.003% v/v). The resulting oil “daughter” droplets are characterized by a chip with integrated microelectrodes, permitting to extract number, velocities and diameter distribution (peaked at about 3 m) employing electrical impedance measurements. In accordance with reported models, the electrical characterizations show that the droplets have volumes in the femtoliter scale and are subjected to inertial focusing. [3] This work can be considered an important advancement for understanding the effects of downscaling on fragmentation phenomena at immiscible interfaces, leading to a knowledge platform for a tailored oil droplets fabrication applicable for drug encapsulation, pharmaceutic preparations, and thin-film wrapping around droplets. [4] Bibliography 1. D. Spencer, F. Caselli, P. Bisegna and H. Morgan., Lab Chip, 2016, 16, 2467. 2. H. Lhuissier, C. Sun, A. Prosperetti, and D. Lohse, Phys. Rev. Lett., 2013, 110, 3. G. Arrabito, V. Errico, A. De Ninno, F. Cavaleri, V. Ferrara, B. Pignataro, and F.Caselli, Langmuir, 2019, 35, 4936. 4. D. Kumar, J. D. Paulsen, T. P. Russell, N. Menon, Science, 2018, 359, 775.
2019
Giuseppe Arrabito, V.E. (2019). Spontaneous Interfacial Fragmentation of Inkjet Printed Oil Droplets and Their electrical characterization. In Book of Abstracts - FISMAT 2019.
File in questo prodotto:
File Dimensione Formato  
Spontaneous Interfacial Fragmentation of Inkjet Printed Oil Droplets and Their electrical characterization FisMat 2019 Book of abstract FisMat 2019.pdf

accesso aperto

Descrizione: Abstract in Atti del Convegno
Tipologia: Versione Editoriale
Dimensione 49.35 kB
Formato Adobe PDF
49.35 kB Adobe PDF Visualizza/Apri

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/10447/378485
Citazioni
  • ???jsp.display-item.citation.pmc??? ND
  • Scopus ND
  • ???jsp.display-item.citation.isi??? ND
social impact